Kit Contains: Soldered Nano compatible, Nano Cable Mini USB to USB ( cable colour might change from the one shown in picture)
Note: Need to install CH341SER driver
Microcontroller Atmel ATmega328 Operating Voltage (logic level): 5V Input Voltage (recommended): 7V ~ 12V Input Voltage (limits): 6V ~ 20 V
Digital I/O Pins: 14 (of which 6 provide PWM output) Analog Input Pins: 8 DC Current per I/O Pin: 40mA
Flash Memory: 32KB (ATmega328) (of which 2 KB used by bootloader) SRAM: 2KB (ATmega328) EEPROM: 1KB (ATmega328) Clock Speed: 16MHz
,
Specification: Ard Nano V3 with USB Cable By Easy Electronics
Brand
‎easy electronics
Manufacturer
‎YKA Store – Coimbatore – TN
Country of Origin
‎China
Colour
‎blue
Number of Memory Sticks
‎1
Item Weight
‎100 g
Product Dimensions
‎5 x 5 x 5 cm, 100 Grams
Item part number
‎ARDUINO_NANO_V3
Item Height
‎5 Centimeters
Item Width
‎5 Centimeters
Processor brand
‎Atmel
Memory Storage Capacity
‎32 KB
Connectivity Technology
‎USB
Are batteries included?
‎No
Hardware Interface Type
‎USB
8 reviews for Ard Nano V3 with USB Cable By Easy Electronics
4.0out of 5
★★★★★
★★★★★
4
★★★★★
2
★★★★★
1
★★★★★
0
★★★★★
1
Write a review
Show allMost HelpfulHighest RatingLowest Rating
★★★★★
prathamesh –
This is a Arduino nano clone thus available at cheaper price, I was just unable to load any sketch on this thing, tried numerous times never succeeded, I bought this one to do the Ambient light setup for my Gaming desk, I tried different Pc’s to load the sketch, all sorts of drivers, different usb cables, every troubleshooting videos on youtube, at the end I had to give up.
Would recommend spending more and getting the original Arduino board.
These clones sometime work sometime they don’t, I did see multiple videos on YouTube using these clones, but i was not able to get this work.
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
Abin Tom Jacob –
Got the product in a well package. This is the clone of original. But it works perfectly as that of original. The usb cable supplied is also a decent one. Also the plasctic box provided was very useful for me. After working with it instead of keeping in the table or in the floor, now I used to keep the board inside the box. Hope this will increase the boards lifetime 🙂
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
Rahul –
There is an error in uploading code but after researching I think there is no fault of arduino In my laptop there is not ch340 driver and i install it and working nicely WHAT DID I DO 1) See the port model no. In device manager 2) Go to the crome and search (model no. Of your cable ) and driver like (___CH340 driver___) 3) Download it and install it 4) Go to arduino idle and select arduino broad, port , change processer to OLD BOOTLOADER and then select programmer 5) Enter code whatever you want and verify it and then download I HOPE NOW YOUR ARDUINO WORK PROERLY
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
amal t p –
Nice product
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
Om –
Value for money is good. But the cable(A-to-B) is not good. It stopped working wheneverit wasn’t bend and today (after 2 years) both aren’t working. Board has problems with avrdude and cable is only able to provide 3V3. By the way nice product but with shorter life span
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
Yash –
Value for money
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
sivasubramanian –
Works as expected
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
Karthik –
I bought it for 399. The cable was faulty. I had to spend antother 100 on cable. the nano clone is working fine. I need install drivers everytime I change the port(They are avilable online). And I have to use old bootloader to upload code.
prathamesh –
This is a Arduino nano clone thus available at cheaper price, I was just unable to load any sketch on this thing, tried numerous times never succeeded, I bought this one to do the Ambient light setup for my Gaming desk, I tried different Pc’s to load the sketch, all sorts of drivers, different usb cables, every troubleshooting videos on youtube, at the end I had to give up.
Would recommend spending more and getting the original Arduino board.
These clones sometime work sometime they don’t, I did see multiple videos on YouTube using these clones, but i was not able to get this work.
Abin Tom Jacob –
Got the product in a well package. This is the clone of original. But it works perfectly as that of original. The usb cable supplied is also a decent one. Also the plasctic box provided was very useful for me. After working with it instead of keeping in the table or in the floor, now I used to keep the board inside the box. Hope this will increase the boards lifetime 🙂
Rahul –
There is an error in uploading code but after researching I think there is no fault of arduino In my laptop there is not ch340 driver and i install it and working nicely
WHAT DID I DO
1) See the port model no. In device manager
2) Go to the crome and search (model no. Of your cable ) and driver like (___CH340 driver___)
3) Download it and install it
4) Go to arduino idle and select arduino broad, port , change processer to OLD BOOTLOADER and then select programmer
5) Enter code whatever you want and verify it and then download
I HOPE NOW YOUR ARDUINO WORK PROERLY
amal t p –
Nice product
Om –
Value for money is good. But the cable(A-to-B) is not good. It stopped working wheneverit wasn’t bend and today (after 2 years) both aren’t working. Board has problems with avrdude and cable is only able to provide 3V3. By the way nice product but with shorter life span
Yash –
Value for money
sivasubramanian –
Works as expected
Karthik –
I bought it for 399. The cable was faulty. I had to spend antother 100 on cable. the nano clone is working fine. I need install drivers everytime I change the port(They are avilable online). And I have to use old bootloader to upload code.