Compatible for Zotac GTX 1060 AMP Edition Graphic Card
,
Specification: inRobert 85mm Video Card Fan Cooler Fan for Zotac GTX 1060 AMP Edition Graphic Card
Brand
‎inRobert
Manufacturer
‎inRobert
Model
‎GA91S2H
Product Dimensions
‎8.5 x 8.5 x 1 cm, 82 Grams
Item model number
‎GA91S2H
Voltage
‎12 Volts
Wattage
‎3 Watts
Batteries Included
‎No
Batteries Required
‎No
Country of Origin
‎USA
Item Weight
‎82 g
5 reviews for inRobert 85mm Video Card Fan Cooler Fan for Zotac GTX 1060 AMP Edition Graphic Card
4.2out of 5
★★★★★
★★★★★
4
★★★★★
0
★★★★★
0
★★★★★
0
★★★★★
1
Write a review
Show allMost HelpfulHighest RatingLowest Rating
★★★★★
Mark Thorne –
Had to remove and disassemble the cooler, but it wasn’t difficult. Works as advertised.
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
Cody Jackson –
TL;DR: Drop-in replacement, keep the screws from your old GPU, nice and quiet, ONLY FOR NON-TI 1070 CARDS.
You get two fans, bubble wrapped and stacked on each other carefully in a decent cardboard box. It comes with a PWM splitter cable. It will NOT have screws (as the product description says), so be sure to save your old ones.
It’s easy enough to install, although routing the shrink-wrapped section of the cable to the connector is a little tricky. You will also need to remove the cooler assembly and flip it to remove the screws holding the fan shroud in place. I recommend doing the cooler removal with a warm (as warm as you can tolerate) card to loosen the thermal compound and pads.
These fans are extremely quiet and balanced. In fact, it’s significantly quieter than the EVGA GTX 1070 SC (ACX 3.0) in my main desktop, which I find odd. I ran gpuburn for an hour and temperatures stabled at 72C and 49% fan speed. Beautiful.
Now for the compatibility issues I see in reviews. I have a 1070 Mini, non TI. Both fans are the same size and both fans have squared-off ends on the 3 mounting tabs.
If you have fans where one is slightly larger than the other, or the old mounting tabs have half-circle ends, these are NOT the fans for you.
Closing thoughts: I ordered this because one of the two fans wobbled (!) enough to hit the shroud. Time will tell if these fans develop the same issues. But so far, they are working fantastically.
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
Brandon Alexander –
Fit correctly and work great zotac mini dual fan 1070.you will need to pull the heatsink off to remove the shroud make sure you have thermal paste on hand to reapply. Also if the pads need replacement its a good time to do it.
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
Frank L Tetro IV –
Works pretty good, I didn’t get to check temps for the old original fans but the new one works good!
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
Cody Jackson –
Upon removing the fans from my Zotac GTX 1070, In triangular shaped mounting bracket was rounded on all 3 ends, instantly I became suspicious because the fans I receieved in my order, had the same triangluar mounting bracket, only this one, was squared on all 3 ends on the bracket. So, I began the disassembly and mounting of the NEW fans, and to my pleasure the FANS fit just fine, how ever the mounting bracket was too small on the new fans. This made it extremely hard to mount as there is no slack or give in any of the holes, and drilling new holes that close would only further ruin the GPU. So, I mounted both sides with 1 screw each leaving the fans with about 1mm of space before any rubbing…thankfully, I dont see this as an issue, however, it is very concerning having a GPU fan mounted with only 1 screw under heavy load and hoping for a good outcome… Thats just playing with fire.
Finally, the wires attached to the new fans are about 2 inches 2 long with so much slack you can barely tuck them in the retainers on the fan shroud. This is actually quite dumb, and the manufacturing process (if there was one) was illogical and badly thought out. When I bent the wires into place to get them to stay, I heard a slight crunch.
I have yet to actually mount and plug the GPU into my PC for fear it might fail and cause even more damage.
I almost never have issues with any purchases on amazon, so to say I had one with this purchase is kind of surprising.
I will not be sending this back for a refund because the box is long gone now, as I didnt anticipate something as simple as a fan to not fit what it was marketed as fitting.
Mark Thorne –
Had to remove and disassemble the cooler, but it wasn’t difficult. Works as advertised.
Cody Jackson –
TL;DR: Drop-in replacement, keep the screws from your old GPU, nice and quiet, ONLY FOR NON-TI 1070 CARDS.
You get two fans, bubble wrapped and stacked on each other carefully in a decent cardboard box. It comes with a PWM splitter cable. It will NOT have screws (as the product description says), so be sure to save your old ones.
It’s easy enough to install, although routing the shrink-wrapped section of the cable to the connector is a little tricky. You will also need to remove the cooler assembly and flip it to remove the screws holding the fan shroud in place. I recommend doing the cooler removal with a warm (as warm as you can tolerate) card to loosen the thermal compound and pads.
These fans are extremely quiet and balanced. In fact, it’s significantly quieter than the EVGA GTX 1070 SC (ACX 3.0) in my main desktop, which I find odd. I ran gpuburn for an hour and temperatures stabled at 72C and 49% fan speed. Beautiful.
Now for the compatibility issues I see in reviews. I have a 1070 Mini, non TI. Both fans are the same size and both fans have squared-off ends on the 3 mounting tabs.
If you have fans where one is slightly larger than the other, or the old mounting tabs have half-circle ends, these are NOT the fans for you.
Closing thoughts: I ordered this because one of the two fans wobbled (!) enough to hit the shroud. Time will tell if these fans develop the same issues. But so far, they are working fantastically.
Brandon Alexander –
Fit correctly and work great zotac mini dual fan 1070.you will need to pull the heatsink off to remove the shroud make sure you have thermal paste on hand to reapply. Also if the pads need replacement its a good time to do it.
Frank L Tetro IV –
Works pretty good, I didn’t get to check temps for the old original fans but the new one works good!
Cody Jackson –
Upon removing the fans from my Zotac GTX 1070, In triangular shaped mounting bracket was rounded on all 3 ends, instantly I became suspicious because the fans I receieved in my order, had the same triangluar mounting bracket, only this one, was squared on all 3 ends on the bracket.
So, I began the disassembly and mounting of the NEW fans, and to my pleasure the FANS fit just fine, how ever the mounting bracket was too small on the new fans. This made it extremely hard to mount as there is no slack or give in any of the holes, and drilling new holes that close would only further ruin the GPU.
So, I mounted both sides with 1 screw each leaving the fans with about 1mm of space before any rubbing…thankfully, I dont see this as an issue, however, it is very concerning having a GPU fan mounted with only 1 screw under heavy load and hoping for a good outcome… Thats just playing with fire.
Finally, the wires attached to the new fans are about 2 inches 2 long with so much slack you can barely tuck them in the retainers on the fan shroud. This is actually quite dumb, and the manufacturing process (if there was one) was illogical and badly thought out. When I bent the wires into place to get them to stay, I heard a slight crunch.
I have yet to actually mount and plug the GPU into my PC for fear it might fail and cause even more damage.
I almost never have issues with any purchases on amazon, so to say I had one with this purchase is kind of surprising.
I will not be sending this back for a refund because the box is long gone now, as I didnt anticipate something as simple as a fan to not fit what it was marketed as fitting.
This sucks…. 1 star.