[EXPAND 4-PIN FAN INTERFACES]: Solving the problem of lack of motherboard fan interfaces. Designed for 12V 4-Pin 3-Pin fans, support simultaneous starting at most 10 channel fans. 10 way 4-pin PWM fan power supply extension hub, it provide a better power supply solution for atx PC computer case internal motherboard cooling fans & cpu fans.
[PC PWM FAN HUB]: In the hub interfaces, the RED CPU interface is the CPU fan dedicated interface (with speed detection function). Since the mainboard can only receive one rotation speed signal, the remaining nine conventional fan interfaces have the PWM function, but no speed signal (Note: all fans can only operate at the same speed).
[SCOPE OF USE]: Plug-n-Play, easy to use. For both 4-Pin and 3-Pin fans. Please note 4Pin fan speed can be adjusted by temperature control. 3Pin fan can also be used, but because 3Pin has no PWM function, it is at fixed speed after inserting. Support 4-pin and 3-pin pc case fans cable. Suitable for CPU or computer case fan.
[EASY TO INSTALL]: There is EVA double-sided adhesive at the back of the hub, which can be easily affixed to a flat place. Also a fixing screw hole in the middle of the PCB to facilitate fixing to a part of the chassis. The fan splitter cable provide additional fan to increase airflow in your computer case. With 3 self adhesive 2mm EVA foam, easy to fixed and not easy to fall.
[OPERATION MODE]: RED is expected to be a pass through for the CPU fan. So, the hub has a power source fed from the computer power supply, then the speed is regulated by the speed for the “source” fan. You can connect to the CPU fan lead on the system board or the chassis fan lead. The ten fans will spin at the same speed, that designated by the system for that fan. If the chassis fan is configured in BIOS to run at 50%, you will have 10 fans at 50%.
,
Specification: Verilux® PC PWM Fan Hub CPU Cooling HUB 10 Port 12V 4 Pin Fan PWM Hub Molex Controller Fan Hub Splitter, 4-Pin PWM Fan Power Supply Extension Cable…
Brand
Verilux
Manufacturer
Verilux
Model
4328444952
Product Dimensions
13.1 x 8.6 x 2.8 cm, 51.6 Grams
Item model number
4328444952
Compatible Devices
Desktop
Mounting Hardware
See Product Description
Number of items
1
Noise Level
30 dB
Voltage
12 Volts
Batteries Included
No
Batteries Required
No
material
Lead
Country of Origin
Hong Kong
Item Weight
51.6 g
8 reviews for Verilux® PC PWM Fan Hub CPU Cooling HUB 10 Port 12V 4 Pin Fan PWM Hub Molex Controller Fan Hub Splitter, 4-Pin PWM Fan Power Supply Extension Cable…
4.5out of 5
★★★★★
★★★★★
5
★★★★★
2
★★★★★
1
★★★★★
0
★★★★★
0
Write a review
Show allMost HelpfulHighest RatingLowest Rating
★★★★★
Akhil Sharma –
It has 3M double sided tape and screw mount holes you can fix it easily inside the PC cabinet. sata power is required. Supports 10 Fans, 3pin and 4pin both fan supported, RGB fan supported.
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
BIJAN –
I have read all the reviews about this product before ordering it, trying to clear the confusion that most people have about it.
1. Only a SATA connection from the power supply will run the fan, but in this case all fans will run at their full speed. In this case, there is no obligation to connect a fan to the red port. You can install the 10 ports according to your convenience.
2. If you want to control the speed of the fan, you must connect it to the motherboard. But in this case you must always put a fan on the red port. Otherwise the speed control will not work. Because the speed control system works only on the red port and the other 9 ports copy the speed of that red port, it means that the same speed as the red port will be on the other 9 ports.
3. It takes Sata connector from power supply not molex.
Additional precautions.
Never install more than 10 fans in this device. Otherwise the capacitor attached to it may get damaged. It is written on the official website of Verilux®.
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
J.Robert –
I have plugged in 6 fans by daisy chaining them to this fan hub. Good for miners and for those who require a lot of fans in their cabinets. Good to buy!
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
Biswajit Rajbanshi –
Works perfect so far. Also the double sided tape really strong. So you need to make your mind before taping it to your case.
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
Abinash –
If you are using 3 pin fans avoid this. It will blow your ear drums off. Buy products with switch or knob for fan control. Not tested with 4 pin fan
Looks good. Hopefully they will revise the product with resistors to lower max fan speed. Circle fans are always noisy when connected to molex/SATA cable
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
Darshan hegde –
Very easy to use and very useful if you have limited ports on motherboard for fans Easy to use, install and works fine.
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
Abinash –
Guys if you need extra fan connector just go for it It works with both 3 and 4 pin fan connector. Happy to have the product 😊 Bought for 600
Akhil Sharma –
It has 3M double sided tape and screw mount holes you can fix it easily inside the PC cabinet. sata power is required. Supports 10 Fans, 3pin and 4pin both fan supported, RGB fan supported.
BIJAN –
I have read all the reviews about this product before ordering it, trying to clear the confusion that most people have about it.
1. Only a SATA connection from the power supply will run the fan, but in this case all fans will run at their full speed. In this case, there is no obligation to connect a fan to the red port. You can install the 10 ports according to your convenience.
2. If you want to control the speed of the fan, you must connect it to the motherboard. But in this case you must always put a fan on the red port. Otherwise the speed control will not work.
Because the speed control system works only on the red port and the other 9 ports copy the speed of that red port, it means that the same speed as the red port will be on the other 9 ports.
3. It takes Sata connector from power supply not molex.
Additional precautions.
Never install more than 10 fans in this device. Otherwise the capacitor attached to it may get damaged. It is written on the official website of Verilux®.
J.Robert –
I have plugged in 6 fans by daisy chaining them to this fan hub. Good for miners and for those who require a lot of fans in their cabinets. Good to buy!
Biswajit Rajbanshi –
Works perfect so far. Also the double sided tape really strong. So you need to make your mind before taping it to your case.
Abinash –
If you are using 3 pin fans avoid this. It will blow your ear drums off. Buy products with switch or knob for fan control. Not tested with 4 pin fan
Looks good. Hopefully they will revise the product with resistors to lower max fan speed. Circle fans are always noisy when connected to molex/SATA cable
Darshan hegde –
Very easy to use and very useful if you have limited ports on motherboard for fans
Easy to use, install and works fine.
Abinash –
Guys if you need extra fan connector just go for it
It works with both 3 and 4 pin fan connector.
Happy to have the product 😊
Bought for 600
BIJAN –
Still working.. go for it… Almost 13 months